Search results

Anyone know the year and model for a GM mini starter straight bolt pattern 153 tooth flywheel. Also does anyone have the part number for the starter to block brace ? Motor is 1973 454

Looking for tips on splitting A/C box apart to replace heater core. I am pretty sure all the bolts are out I can wiggle it around quite a bit. I read it has to be lifted straight up to be removed. Trying to not break it but it is not coming off. Any suggestions would be appreciated.

Someone have a picture of stock upper control arm installed. Replaced my bushings and in the process got them mixed up between drivers and passengers side. I am sure at some point it will be obvious if it is correct or not. Just wanted to know before I started to reinstall. Thanks

Not a Malibu. My 2003 Cavalier. Battery was getting some age and cranking slow on cold mornings . No other issues. Replaced the battery after about 1 minute gauges all go down . Check gauges, theft system and the wrench light come on . Car is still running fine. Turn off head lights and gauges...

Flat, satin, semi gloss or gloss. Mine have been painted a few times. I have them out and wanted to repaint them correctly.

Fan works fine on all speeds except high. I would think that points to the fan switch inside the car and the resistor is fine. What do you think ?

Put a Astro steering shaft on and at the same time replaced my manual steering box with a rebuilt one. Reusing my old pitman arm . Steering wheel is 90 degrees to the right when I am going straight. I don't see anyway to rotate the steering wheel because of the horn wire. Anyone know how to...

Looking to purchase a 22 rifle. Wondering what you have and like. Been looking at a Marlin Model 60 and some Henry's. Thanks

Have 2 maybe related. Car shut off going 45 I have no spark. Need to trouble shhot that have 12V+ at Batt term on HEI dist. It is a Mallory with a Mallory Coil and cap. Put another coil and cap on nothing. I have the original HEI dist. I can put in but wanted to trouble shoot a little before...

3 or 4 terminal ? Does it matter I see both.

Would someone measure the distance from the passenger side edge of the trunk to the edge of the CHEVROLET emblem. Looks to me like from top to bottom it is in the middle. Thanks

8.5 open $500. I would be replacing my 7.5. Wondering about how much I would have in it to be back to a 3.73 Posi in the 8.5. Almost exclusively a street car may make it to the strip once in awhile. 461 not stock but mild 4 speed Muncie. Also a 7.5 3.73 drum to drum worth about $250 ??

I have a slight vibration that I am tracking down. Did not think it was tires but did put a different set on. About 50 MPH on up no worse as speed increases. Felt it was in the rear of car. No steering wheel vibration but see it in the rear view mirror. Up on jack stands I feel it with the drive...

I need to install a diode inline. If the car is hot when I shut off the key the engine continues to run until the electric fan stops turning. It is a single Flex A Lite not sure exactly what current it is pulling. Had some LED's lying around first one was to big. LED would light but fan would...

I am sure I am going to need to do this with the 275x60x15 tires and 15x8.5 with 3.81 " BS on the wheels. What is the best method to use to do rhis. I do not want to take a chance of doing any noticeble damage to the quarter. Thanks

Guy at Jegs said they might stick out a little more than I might want. What do you think ? 15x8.5 wheels 3.81" BS . Tires 275-60-15. Rub frame, need to roll fenders ? Thanks

I did not try and force it in. The specs. on my new bushing call for a 1.093 OD it is actually 1.095. Is that enough to make it not go in ? Should I try and tap it in or get another one ?

Going with a 215/70/15 front tire. Which wheel would look better a 15x6 or a 15x7 both have 3".75 back space ?

2 dr. Malibu. I am looking at 215/70/15 's front 275/60/15's back. Cannot decide on 6" or 7" wheels in the front. And using 8.5" in back . All wheels are 3.81" BS. Opinions on front wheel width and any other thoughts.

Currently I have a BBC , manual linkage and a 153 tooth flywheel. This winter I am putting in a 454 . I am looking for a flywheel for it that is 153 tooth so I can retain everything else. In the future I may switch to hydraulic linkage and maybe a 5 or 6 speed. My question is the flywheel I need...