Search results

  1. lasttime78

    Re-installing C Pillar Plastic

    Position the clip where you want it with masking tape around the slot that goes to the back side of sail panel. It will hold it in place while you install the panel. Hope this helps.
  2. lasttime78

    Pinion angle help please!

    x2, Must be level before you start!!!!
  3. lasttime78

    What did U do to your G-body today??

    That stripe looks good! For a detail in size for car I would shorten it up at the tail end. The tail light extension area by maybe one to two inches instead of going to the end like that. It would look more proportionable. JMO Looks good though!!!!!!!!
  4. lasttime78

    What did U do to your G-body today??

    Got two extra rims to mount up some slicks this year to play a little and polished them up, one down one to go. Also had buddy load up and unload the tires and rim job today, got the old rear tires swapped out with new 295's again. Going real slow!! its only been 15 days since 2nd back surgury...
  5. lasttime78

    2" drop spindles vs traction.

    The only thing I see that you need to do is clean the rubber off behind the rear tires and maybe a nice tint job. Looks like my last car alot.
  6. lasttime78

    What did U do to your G-body today??

    Well for the last two weeks I have been spending all day out in shop working on the Malibu = I have put in new front coil springs, inner and outer tie rods, new KYB shocks front and rear, new quick silver shifter, fabbed up new console top, new Monster trans 700r4 (the super duty BBC ) it's...
  7. lasttime78

    What cam for stock SBC 400 engine????'s

    The Xe262H would be a better choice for your set-up. IMO
  8. lasttime78

    2" drop spindles vs traction.

    I would leave it as it is. You put 2" drop spindles in you can say good bye to lifting the front end like you were in the picture there.
  9. lasttime78

    What did U do to your G-body today??

    Glad i took advantage of the nice 34 degree day this last Sunday and moved Malibu from little barn up to the shop. Stared at her today why I filled up the tractor to get ready to Snow Plow for are Blizzard tomorrow 10 to 19 inches of snow in 12 hour period. Maybe get snowed in up to the shop and...
  10. lasttime78

    G Body newbie needing interior help please :(

    Putting it in and out is easier with pass. inner fender off. It will piece of cake. You wanting to put air in, or just heat???? I went from ac cars to heat only on all 7. I need the room for the big block. Have any questions ask. Jim
  11. lasttime78

    Trying to 15/10 with slicks

    Do a frame notch,roll fender lip and run 15x10 with 4.50 and all is good.
  12. lasttime78

    NEED HELP CHANGING STEERING COLUMNS

    Yup, What did you get to use between the double d-shap and 27 spline shaft on the Malibu? I think its 27 don't remember?
  13. lasttime78

    NEED HELP CHANGING STEERING COLUMNS

    I am doing samething this winter going to tilt on the floor column. Keep it simple the way it is now. easier to change the swithches out when they go bad, also who is going to know if they work other than you???? Whats up?
  14. lasttime78

    TH-400 "Ears"

    You will lose the outer screw holes for the flywheel cover!!!!! LOL You won't hurt anything, just a little strength in that area of the trans case. Take what little you need off.
  15. lasttime78

    What did U do to your G-body today??

    Air shocks???????????????????? This isnt the 80's man. Just messing with ya.
  16. lasttime78

    Launching

    She did spin, your 60 foot times show that?
  17. lasttime78

    How much will 10 bolt rear take

    A Rear end is only as good as the parts you put into it! Regardless what size, JD Racing and Resterations (Jim) says with right parts 7.5 will handle up to 800 horse. No problem? He more expierance than us he builds rear-end for people. [-X [-X [-X
  18. lasttime78

    What did U do to your G-body today??

    Rebuilt the alternator today, so much cheaper than buying a so called rebuilt one. Most places sell rebuilts and all they do is clean up the cases and replace the part that is bad and put it on the shelf to sell to auto parts distributor. Napa, Auto Zone and Advance do this practice by the way...
  19. lasttime78

    What did U do to your G-body today??

    Gave Malibu an attitude adjustment !!!!!! Need to get new rear drop springs now.
  20. lasttime78

    80 malibu sit on the fenders. how do i make it stop!!!!

    x2 Thats how I understood it.(REAR) What he said ^