I took my transmission off my motor when I pulled it from my old cutlass. I tossed the converter and put on a B&M holeshot my friend had lying around. He had used it before for a few miless so there might have been some fluid in it but I don't remember and didn't add any to it. I filled the pan...
Really dumb question that I can't seem to find the answer on. Does the brake hose mount to the top of the caliper or the bottom of the caliper? I had them mounted so the hose would go to the top but it didnt seem like it wanted to fit very well. I swapped sides so the hose goes to the bottom of...
I have a tach/speedo assembly but the back of the tach has a switch to change from v8-v6. Mine is broken off and doesn't specify what way is what. Does anyone know if left is v8 or right is v8? I can toss up a picture later to help show what Im talking about. thanks.
I for some reason lost the spedometer housing and gear from my transmission out of a 76 Cutlass. Its a th350 and has one that looks like this:
I'm not sure how to figure out what gear I need though. I noticed there's a difference in how many teeth the gear has, and also has to match the axle...
Just recently finished my semi build of a 76 olds 350. Here is whats on it so everyone knows:
Stock block and rotating assembly (7x,*** miles)
New oil pump (Melling high volume, bolt on screen)
Edelbrock double timing set
Edelbrock performer cam/lifters/springs
Edelbrock performer rpm intake...
Anyone know where I can get front backing plates that attach to the spindle for the front. All I can find is for the rear. Either that or does anyone have a set in good condition? Thanks.
I have a 1980 LeMans and was wondering if anyone can give me a diagram of what each pin on the plug that bolts into the firewall (under brake booster) is for. If you need a picture of my specific plug I can get that, thanks.
Building an oldsmobile 350. Its going to have w31 heads with compression probably around 9:1. Roller rockers, full cam and valvetrain upgrade, full length headers, th350, performer rpm intake and holley 750. Power will be made in the lower rpm range for a street car. I have an msd 6al box. Is it...
Was toying around the idea of slapping a centrifugal supercharger on the (1976) olds 350 I have. It will be stock with a performer rpm intake, roller rockers, holley 750, and full length headers. Is there such a thing as buying a used supercharger and throwing it on with low psi for the weekend...
I know this may not be here but I figured if someone knows about electrical they could help. I have a 99 intrepid that I will be adding a sound system in. Its going to be using a Sundown SAZ-1500d amplifier hooked up to a 12 inch Fi Q sub. It will be 800watt rms. I will also be installing an amp...
What type of manifold would you be looking for in a turbo build. I've mostly seen the high rise intakes on builds. Has there been any proven facts that one style is better than another? Thanks.
Anyone have any pictures of a low mounted turbo set up. Either single or twin. I've heard of turbo in the trunk but what about right at the end of a normally mounted header or something? Would be cool for a little stealth build.
I got an fbody sway bar. I found a cutlass with a stock rear sway bar. Should I grab that one and sell the fbody bar? Any difference in performance from the two?
I have some old rims I got from a friend. Two of them are on my car now but the other two are missing a few of the press in adapters that fit into the wheel stud holes. Does anyone know where I can locate these? Thanks.
I have an HEI distributor in my motor. I am going to be using a 6AL msd box. I also have a msd blaster 3 coil. I like the look of the points style cap with the external coil terminal in the middle. I found this conversion but don't really like the look:
Do they have a cap conversion so it...
I'm building a mild Olds 350 and just realized I don't want to waste it all if my converter is no good. Here is what I got so far.
Olds 350 stock bottom end.
Edelbrock cam: 204/214 Duration 448/472 Lift
Stock ratio roller rockers
Edelbrock performer intake
Double roller timing chain
Holley 750...
Trying to plan for my swap since it's my daily driver. I'm swapping an Olds 350/th350 from a 76 Cutlass into an 80 LeMans that originally had a 229 Chevy with the th200 trans and a 7.5 rear. The rear and driveshaft are still sitting in the car. Will the Olds th350 trans fit in that with that...
Anyone know what the fuel gauge wire colors are? I took out the fuel/dummy lights gauge and i need to wire in an aftermarket fuel gauge. I think the ones I need are brown and brown/white. Thanks.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.